Styrkortet för Prime finns inbyggt i Essensse Neo 4 redan vid leverans. För att kunna hantera kortet behöver du komplettera med manöverpanelen Prime. Inuti panelen hittar du anslutningsinformation som du använder för att koppla Prime mot WiFi. Läs instruktionerna nedan och i manualen innan du startar installationen.
Komplettera Prime med någon av dörrkontakterna samt en VIM ventilsats. Under Tillbehör hittar du modeller och storlekar som kan passa bra.
Anslut en mobil / smartphone till Prime manöverpanel
Ladda ner och installera Prime-appen på din mobil. Om du använder länkarna på den här sidan hittar du lätt rätt app.
Öppna sedan manöverpanelen för att kunna ansluta mobilen till WiFi-kontrollen med kameran. På insidan av manöverpanelen hittar du en etikett med den information du behöver för anslutningen (se bilden nedan).
Öppna Prime-appen på din mobil och gör klart anslutningen där. Sedan är det bara att börja ställa in de funktioner du vill använda. Läs mer i manualen, där hittar du utförlig information.
Eftersom Essensse Neo 4 har Prime styrkort inbyggt redan vid leverans behöver du bara komplettera med manöverpanelen. Även om du styr flera luftridåer med Prime samtidigt räcker det med en manöverpanel. Ridåerna styrs sedan gemensamt via den panelen.
Manöverpanelen har stor display och touchscreen, vilket gör det enkelt att komma åt standardfunktionerna. Du kan även koppla upp den mot WiFi och styra luftridån via smartphone. Som standard ingår ModBus RTU. Som tillval finns ModBus TCP/IP.
Kom ihåg att även komplettera med någon av dörrkontakterna samt en ventilsats.
Dimensioner för Prime
Vikt: 700 g
Information & Manualer
Övrigt
Modbus protokoll
Protokollet gäller för Modbus RTU-kommunikation. Kommunikationsbeskrivningen gäller för alla produkttyper. Holding-protokollen används för kontroll av produkten. Input-protokollen används för att läsa av aktuell status för produkten.
Innan du styr produkten via Modbus är det nödvändigt att läsa produktens manual för att känna till exakt vilka funktioner som stöds i de olika lägena! Användningen av protokollen beror på produktens hårdvarukonfiguration, dvs. om den är vattenvärmd, elvärmd etc, samt på aktuellt läge och inställningar i servicemenyn.
- Funktioner
- Input factory
- Holding service
- Input status
- Input slave status
- Holding share
- Holding BMS temp. sensors
| HOLDING REGISTERS | FUNC CODE |
|---|---|
| SERVICE | 0x03,0x06,0x10 |
| SHARE | 0x03,0x06,0x10 |
| INPUT REGISTERS | |
| FACTORY | 0x04 |
| STATUS_AC | 0x04 |
| SLAVE_AC_STATUS | 0x04 |
| DEFAULT MODBUS RTU SETTINGS | |
| Modbus Unit Address | 1 |
| Baudrate | 9600 |
| Parity | ODD |
| Stop Bits | 1 |
| PLC Addresses - BASE1 |
Värden representeras som osignerade 2xByte.
Protokollet för Input factory är ett indataregister som används för tillverkarens ändamål.
| Address | Name | Info | Min. Value | Max. Value | Default | Enum |
|---|---|---|---|---|---|---|
| 31000 | Reserved | Reserved | 0 | 65535 | 0 | |
| 31001 | ID | ID unit | 0 | 65535 | 525 | Prime ID = 525 |
| 31002 | Locality | Locality of instalation | 0 | 1 | 0 | EU = 0 / USA = 1 |
| 31003 | Fan type | Type of fan | 0 | 3 | 0 | Motor EC = 0 / Motor AC = 1 (reserved) |
| " | " | 0 | 3 | 0 | Motor AC3 = 2 (3 stp level) / Motor AC5 = 3 (5 stp level) | |
| 31004 | Heat type | Type of fan heating exchanger | – | – | – | Post heat none = 0 / Electric = 1 / Water = 2 |
| " | " | – | – | – | WCO = 3 (reserved) / DX = 4 (reserved) / WC = 5 (reserved) | |
| 31005 | Modbus Baudrate | Modbus Baudrate | 4800 | – | 19200 | 4800 / 9600 / 14400 / 19200 / 38400 |
| 31006 | Modbus Parity | Modbus Parity | 0 | 2 | 1 | None = 0 / Odd = 1 / Even = 2 |
| 31007 | Modbus address port | Modbus address port | 1 | 247 | 1 | |
| 31008 | Serial number H | Serial number | 0 | 65535 | 0 | |
| 31009 | Serial number L | Serial number | 0 | 65535 | 0 | |
| 31010 | FW F0 | Microcontroller firmware number | 0 | 65535 | 0 | |
| 31011 | FW WT | WiFi firmware number | 0 | 65535 | 0 | |
| 31012 | Motor max pwm limit | Motor power limitation percent | 20 | 100 | 100 | |
| 31013 | Reserved | Reserved | 0 | 65535 | 0 | |
| 31014 | Reserved | Reserved | 0 | 65535 | 0 | |
| 31015 | Reserved | Reserved | 0 | 65535 | 0 | |
| 31016 | Reserved | Reserved | 0 | 65535 | 0 | |
| 31017 | Reserved | Reserved | 0 | 65535 | 0 | |
| 31018 | Reserved | Reserved | 0 | 65535 | 0 | |
| 31019 | Reserved | Reserved | 0 | 65535 | 0 | |
| 31020 | Reserved | Reserved | 0 | 65535 | 0 | |
| 31021 | Reserved | Reserved | 0 | 65535 | 0 | |
| 31022 | Reserved | Reserved | 0 | 65535 | 0 |
Protokollet för Holding service används för att ställa in och kontrollera parametrar i produktens servicemeny. En funktion för fabriksåterställning återställer parametrarna till standardvärden.
| Adress | Namn | Info | Min. Value | Max. Value | Default | Enum |
|---|---|---|---|---|---|---|
| 40201 | Cp pin | Control panel PIN | 0 | 99 | 0 | 0 = without PIN |
| 40200 | Subunits | Number of subunits (modbus slaves) | 1 | 10 | 1 | |
| 40202 | Auto Speed Control Enable | Fan autospeed control – enabling function | 0 | 1 | 0 | |
| 40203 | Heat mode | Automatic heating mode enable (PID control) | 0 | 1 | 1 | 0 = disable |
| 40204 | Door Contact Fixed OverRun Enable | Door contact mode – enabling and specifying the function | 0 | 2 | 1 | Overrun mode / 0 = disable / 1 = time interval / 2 = driving by temperature |
| 40205 | Door Contact Fixed OverRun Minflow Time | Overrun time on minimal fan speed | 5 | 300 | sec | |
| 40206 | Door Contact Fixed OverRun Maxflow Time | Overrun time on maximal fan speed | 5 | 300 | sec | |
| 40207 | Door Contact Fixed OverRun Temp Setpoint | Setpoint for Door contact overrun function driving by temperature | 15°C / 59°F | 30°C / 86°F | 20°C / 68°F | |
| 40208 | Outside Temp Sensor Air Curtain | Outside temperature sensor location | 0 | 2 | 1 | 0 = disable / 1 = EXT1 temperature from Modbus slave 1 (subunit) / 2 = BMS |
| 40209 | Door Contact Fixed OverRun Temp Select | Selection for Door OverRun sensor | 0 | 1 | 0 | 0 = CT room / 1 = thermostat |
| 40210 | Temp Sensor Selection | Feedback for automatic temperature control | 0 | 4 | 2 | 2 = room / 3 = thermostat / 4 = room BMS |
| 40211 | Prefer Manual Output | 0 | 1 | 0 = digital / 1 = analog | ||
| 40212 | Pid P | PID proportional range °C/°F according Locality (adr. 31002) | 5°C / 41°F | 60°C / 140°F | 20°C / 68°F | |
| 40213 | Pid I | PID integration time (s) | 1 | 255 | 60 | |
| 40214 | Pid D | PID derivate time (s) | 0 | 10 | 0 | |
| 40215 | Door Contact Logic | Logic of door contact | 0 | 1 | 1 | 0 = NO O / 1 = NO C |
| 40216 | Ext Ctrl Logic | Logic of external control contact | 0 | 1 | 0 | 0 = NO O / 1 = NO C |
| 40217 | Room Therm Logic | Logic of room thermostat contact | 0 | 1 | 0 | 0 = NO O / 1 = NO C |
| 40218 | Ext Ctrl Function | Function of external control contact | 0 | 1 | 0 | 0 = Ext ctrl disable / 1 = Ext ctrl enable |
| 40219 | Antifreeze Temp Air Set | Antifreeze air temperature | 5°C / 41°F | 15°C / 59°F | 5°C / 41°F | |
| 40220 | Antifreeze Temp Wout Set | Antifreeze water return temperature | 10°C / 50°F | 20°C / 68°F | 10°C / 50°F | |
| 40221 | Door SW local | Type of door switch (local / global) | 0 | 1 | 0 | 0 = global door switch / 1 = local door switch |
| 40222 | Fan tacho enable | Enable tacho input for EC fan | 0 | 1 | 1 | 0 = disable Tacho / 1 = enable Tacho |
| 40223 | Alarm heater enable | Enable TK input for heater | 0 | 1 | 1 | 0 = TK disable / 1 = TK enable |
| 40224 | DoorContactEnable | Enable / disable door contact | 0 | 1 | 1 | 0 = door contact disable / 1 = dorr contact enable |
| 40225 | Filter timer max | Maximum time for maintenance in hours | 0 | 4500 | 4500 | 0 = disable maintenance interval |
| 40226 | Auto Speed Control Delta T | Delta T for automatic speed control changes | 1 | 5 | 1 | |
| 40227 | Summer Heat Enable | Enable summer heat blocation | 0 | 1 | 0 | |
| 40228 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40229 | Winter Mounth Start | Mounth when winter starts | 1 | 12 | 1 | |
| 40230 | Winter Mounth Stop | Mounth when winter ends | 1 | 12 | 1 | |
| 40231 | Summer Temp Heater Enable | Limit temperature to enable heat in summer | 10°C / 50°F | 20°C / 68°F | 15°C / 59°F | |
| 40232 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40233 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40234 | Valve excercising – enable | Enable valve excercising for water exchanger | 0 | 1 | 0 | 0 = disable |
| 40235 | Valve excercising – time | Time of valve excercising for water exchanger | 1 | 120 | 60 | |
| 40236 | Valve bleeding | Valve bleeding, prevence of freezing water exchanger | 0 | 30 | 0 | |
| 40237 | Door close fan on off – enable | If the door is closed, it turns off the fan when enable | 0 | 1 | 0 | |
| 40238 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40239 | Door close fan on off – delay | Time delay before fan turn off after setpoint reached | 0 | 120 | 20 | |
| 40240 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40241 | Door fan limit open min | Minimal fan speed for open doors | EC-fan 15 / AC3-fan 33 / AC5-fan 20 | EC-fan 40 / AC3-fan 66 / AC5-fan 40 | EC-fan 15 / AC3-fan 33 / AC5-fan 20 | |
| 40242 | Door fan limit open max | Maximal fan speed for open doors | EC-fan 40 / AC3-fan 66 / AC5-fan 40 | 100 | EC-fan 15 / AC3-fan 33 / AC5-fan 20 | |
| 40243 | Door fan limit close min | Minimal fan speed for close doors | EC-fan 15 / AC3-fan 33 / AC5-fan 20 | EC-fan 40 / AC3-fan 66 / AC5-fan 40 | EC-fan 15 / AC3-fan 33 / AC5-fan 20 | |
| 40244 | Door fan limit close max | Maximal fan speed for close doors | EC-fan 40 / AC3-fan 66 / AC5-fan 40 | 100 | EC-fan 15 / AC3-fan 33 / AC5-fan 20 | |
| 40245 | Antifreeze sensors enable | bit 0 – Air | 0 | 1 | 1 | |
| " | bit 1 – Water | 0 | 1 | 1 | ||
| " | bit 2 – TK | 0 | 1 | 0 | ||
| 40246 | Water return limit enable | Enable water return limitation | 0 | 1 | 0 | |
| 40247 | Water return limit – temperature | Temperature limit of return water | 15 | 85 | 50 | |
| 40248 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40249 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40250 | Global Door Contact – enable | Enable of global door contact (from Modbus subunits number 1) | 0 | 1 | 1 | |
| 40251 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40252 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40253 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40254 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40255 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40256 | Reserved | Reserved | 0 | 65535 | 0 |
Protokollet för Input status används för att läsa av aktuell status för luftridån. Exempel på detta är faktiskt läge, luftflöden, temperaturer, varmvattenberedarstatus, fel etc.
| Adress | Namn | Info | Min. Value | Max. Value | Enum |
|---|---|---|---|---|---|
| 31100 | FW number | ||||
| UNIT GLOBAL STATUS | |||||
| 31101 | bit0 | OFF / ON | 0 | 1 | Off / On |
| bit1 | Automatic heat | 0 | 1 | Autoheat non / Autoheat mode | |
| bit2 | Automatic flow | 0 | 1 | Autoflow non / Autoflow mode | |
| bit3 | Reserved | 0 | 1 | ||
| bit4 | Timeswitch | 0 | 1 | Time SW non / Time SW mode | |
| bit5 | Cooldown | 0 | 1 | Cool dwn non / Cool dwn mode | |
| bit6 | Water Heater antifreeze protection | 0 | 1 | AT freeze ok / AT freeze | |
| bit7 | Water Heater waiting for hot water | 0 | 1 | Hot water non / Hot water | |
| bit8 | Summer Heat | 0 | 1 | Winter / Summer | |
| bit9 | Open Door | 0 | 1 | Closed door / Open door | |
| bit10 | Door After Running | 0 | 1 | Afterrunning non / Afterrunning mode | |
| bit11 | Heater Under Power | 0 | 1 | ||
| bit12 | Reserved | 0 | 1 | ||
| bit13 | Reserved | 0 | 1 | ||
| bit14 | Reserved | 0 | 1 | ||
| bit15 | Reserved | 0 | 1 | ||
| SOFTWARE ERROR | |||||
| 31102 | bit0 | Sw Fan Error | 0 | 1 | |
| bit1 | Reserved | 0 | 1 | ||
| bit2 | Sw Filter Error | 0 | 1 | ||
| bit3 | Sw Filter Warning | 0 | 1 | ||
| bit4 | Sw Heater Error | 0 | 1 | ||
| bit5 | Reserved | 0 | 1 | ||
| bit6 | Reserved | 0 | 1 | ||
| bit7 | Sw Global Error | 0 | 1 | ||
| bit8 | Cfg File Error | 0 | 1 | ||
| bit9 | Reserved | 0 | 1 | ||
| bit10 | Alarm temp room | 0 | 1 | ||
| bit11 | At Freeze cnt overflow | 0 | 1 | ||
| SOFTWARE ERROR 1 | |||||
| 31103 | Reserved | ||||
| SENSOR STATUS | |||||
| 31104 | bit0 | Temp Room St - Room temp. From Control Panel | 0 | 1 | OK / ERROR |
| bit1 | Temp Room Shared St | 0 | 1 | OK / ERROR | |
| bit2 | Outside Temp Sensor Shared | 0 | 1 | OK / ERROR | |
| bit3 | Outside Temp Sensor Bms St | 0 | 1 | OK / ERROR | |
| bit4 | Room Temp Sensor Bms St | 0 | 1 | OK / ERROR | |
| bit5 | Reserved | 0 | 1 | OK / ERROR | |
| bit6 | Reserved | 0 | 1 | OK / ERROR | |
| bit7 | Reserved | 0 | 1 | OK / ERROR | |
| RESERVED | |||||
| 31105 | bit0 | Status DI 1 Door shared | 0 | 0 | OK / ERROR |
| bit1 | Status DI 2 Room Thermostat shared | 0 | 0 | OK / ERROR | |
| bit2 | Status DI 3 Ext Control shared | 0 | 1 | OK / ERROR | |
| bit3 | Status DI 4 Room Thermostat shared | 0 | 1 | OK / ERROR | |
| bit4 | Reserved | 0 | 1 | OK / ERROR | |
| bit5 | Reserved | 0 | 1 | OK / ERROR | |
| bit6 | Reserved | 0 | 1 | OK / ERROR | |
| bit7 | Reserved | 0 | 1 | OK / ERROR | |
| bit8 | Reserved | 0 | 1 | OK / ERROR | |
| bit9 | Reserved | 0 | 1 | OK / ERROR | |
| bit10 | Reserved | 0 | 1 | OK / ERROR | |
| bit11 | Reserved | 0 | 1 | OK / ERROR | |
| bit12 | Reserved | 0 | 1 | OK / ERROR | |
| bit13 | Reserved | 0 | 1 | OK / ERROR | |
| bit14 | Reserved | 0 | 1 | OK / ERROR | |
| bit15 | Reserved | 0 | 1 | OK / ERROR | |
| OUTPUT STATUS | |||||
| 31106 | bit0 | Status DO 3 Run indication | 0 | 1 | Heat closed / Heat open |
| bit1 | Status DO 4 Error | 0 | 1 | Heat closed / Heat open | |
| bit2 | Reserved | 0 | 1 | ||
| bit3 | Reserved | 0 | 1 | ||
| bit4 | Reserved | 0 | 1 | ||
| bit5 | Reserved | 0 | 1 | ||
| bit6 | Reserved | 0 | 1 | ||
| bit7 | Reserved | 0 | 1 | ||
| bit8 | Reserved | 0 | 1 | ||
| bit9 | Reserved | 0 | 1 | ||
| bit10 | Reserved | 0 | 1 | ||
| bit11 | Reserved | 0 | 1 | ||
| bit12 | Reserved | 0 | 1 | ||
| bit13 | Reserved | 0 | 1 | ||
| bit14 | Reserved | 0 | 1 | ||
| bit15 | Reserved | 0 | 1 | ||
| 31107 | Fan Speed | % of fan power | 0 | 100 | |
| 31108 | Sensors Troom temperature | °C (°F) | -40 (-40) | 100 (212) | |
| 31109 | Sensors Troom status | °C (°F) | -40 (-40) | 100 (212) | |
| 31110 | Sensors Outside temperature | °C (°F) | -40 (-40) | 100 (212) | |
| 31111 | Sensors Outside status | °C (°F) | -40 (-40) | 100 (212) | |
| 31112 | Reserved | Reserved | 0 | 65535 | |
| 31113 | Power Heater | % | 0 | 100 | |
| 31114 | Temp Outside BMS | °C (°F) | -40 (-40) | 100 (212) | |
| 31115 | Room BMS | °C (°F) | -40 (-40) | 100 (212) | |
| 31116 | Maintanance Percent | % | 0 | 100 | |
| 31117 | Reserved | Reserved | 0 | 65535 | |
| 31118 | Reserved | Reserved | 0 | 65535 | |
| 31119 | Temperature setpoint | °C (°F) | 5(41) | 45(113) | |
| 31120 | Reserved | Reserved | 0 | 65535 | |
| 31121 | Reserved | Reserved | 0 | 65535 | |
| 31122 | Reserved | Reserved | 0 | 65535 | |
| 31123 | Reserved | Reserved | 0 | 65535 | |
| 31124 | Reserved | Reserved | 0 | 65535 | |
| 31125 | Reserved | Reserved | 0 | 65535 | |
| 31126 | Reserved | Reserved | 0 | 65535 | |
| 31127 | Reserved | Reserved | 0 | 65535 | |
| 31128 | Reserved | Reserved | 0 | 65535 | |
| 31129 | Reserved | Reserved | 0 | 65535 | |
| 31130 | Reserved | Reserved | 0 | 65535 | |
| 31131 | Reserved | Reserved | 0 | 65535 | |
| 31132 | Reserved | Reserved | 0 | 65535 | |
| 31133 | Reserved | Reserved | 0 | 65535 | |
| 31134 | Reserved | Reserved | 0 | 65535 |
Protokollet för Input slave status används för att läsa av aktuell status för slave-luftridåer (aktuellt läge, fläkthastighet, temperaturer, varmvattenberedarstatus, fel etc.
| Address | Name | Info | Min. Value | Max. Value | Enum |
|---|---|---|---|---|---|
| SLAVE 1 | |||||
| Unit global status | |||||
| 31200 | bit0 | OFF / ON | 0 | 1 | OFF / ON |
| bit1 | Cooldown | 0 | 1 | COOLDWN NON / COOLDWN MODE | |
| bit2 | Water Heater antifreeze protection | 0 | 1 | AT FREEZE OK / AT FREEZE | |
| bit3 | Heater Overheat | 0 | 1 | ||
| bit4 | Open Door | 0 | 1 | CLOSED DOOR / OPEN DOOR | |
| bit5 | Door AfterRunning | 0 | 1 | AFTERRUNNING NON / AFTERRUNNING MODE | |
| bit6 | Sensor Flow Alarm St | 0 | 1 | OK / ERROR | |
| bit7 | reserved | 0 | 1 | ||
| bit8 | reserved | 0 | 1 | ||
| bit9 | Temp W Out St | 0 | 1 | OK / ERROR | |
| bit10 | Sw Fan Error | 0 | 1 | ||
| bit11 | Sw Heater Error | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | reserved | 0 | 1 | ||
| bit14 | Sw Global Error | 0 | 1 | ||
| bit15 | Communication Error | 0 | 1 | ||
| IO Status | |||||
| 31201 | bit0 | Status DI 1 Safety Therm 1 | 0 | 1 | OK / ERROR |
| bit1 | Status DI 2 Ext Control | 0 | 1 | OK / ERROR | |
| bit2 | Status DI 3 Room Thermostat | 0 | 1 | OK / ERROR | |
| bit3 | Status DI 4 Door | 0 | 1 | OK / ERROR | |
| bit4 | Status DI TACHO 1 | 0 | 1 | OK / ERROR | |
| bit5 | reserved | 0 | 1 | ||
| bit6 | reserved | 0 | 1 | ||
| bit7 | reserved | 0 | 1 | ||
| bit8 | Status DO 1 Heat1 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit9 | Status DO 2 Heat2 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit10 | Status DO 3 Water pump | 0 | 1 | W PUMP A OFF / W PUMP A ON | |
| bit11 | Heater Under Power | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | At Freeze cnt overflow | 0 | 1 | ||
| 31202 | Air Flow Fan Manual | ‰ of fan power | 0 | 1000 | ‰ of fan power |
| 31203 | reserved | reserved | 0 | 0 | |
| 31204 | reserved | reserved | 0 | 0 | |
| 31205 | Temp W Out – Water return | °C (°F) | –40 (–40) | 100 (212) | |
| 31206 | Sensor Flow Alarm | 0 | 1 | ||
| 31207 | Power Heater | % | 0 | 100 | |
| Tacho Board | |||||
| 31208 | reserved | reserved | |||
| 31209 | reserved | reserved | |||
| SLAVE 2 | |||||
| Unit global status | |||||
| 31210 | bit0 | OFF / ON | 0 | 1 | OFF / ON |
| bit1 | Cooldown | 0 | 1 | COOLDWN NON / COOLDWN MODE | |
| bit2 | Water Heater antifreeze protection | 0 | 1 | AT FREEZE OK / AT FREEZE | |
| bit3 | Heater Overheat | 0 | 1 | ||
| bit4 | Open Door | 0 | 1 | CLOSED DOOR / OPEN DOOR | |
| bit5 | Door AfterRunning | 0 | 1 | AFTERRUNNING NON / AFTERRUNNING MODE | |
| bit6 | Sensor Flow Alarm St | 0 | 1 | OK / ERROR | |
| bit7 | reserved | 0 | 1 | ||
| bit8 | reserved | 0 | 1 | ||
| bit9 | Temp W Out St | 0 | 1 | OK / ERROR | |
| bit10 | Sw Fan Error | 0 | 1 | ||
| bit11 | Sw Heater Error | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | reserved | 0 | 1 | ||
| bit14 | Sw Global Error | 0 | 1 | ||
| bit15 | Communication Error | 0 | 1 | ||
| IO Status | |||||
| 31211 | bit0 | Status DI 1 Safety Therm 1 | 0 | 1 | OK / ERROR |
| bit1 | Status DI 2 Ext Control | 0 | 1 | OK / ERROR | |
| bit2 | Status DI 3 Room Thermostat | 0 | 1 | OK / ERROR | |
| bit3 | Status DI 4 Door | 0 | 1 | OK / ERROR | |
| bit4 | Status DI TACHO 1 | 0 | 1 | OK / ERROR | |
| bit5 | reserved | 0 | 1 | ||
| bit6 | reserved | 0 | 1 | ||
| bit7 | reserved | 0 | 1 | ||
| bit8 | Status DO 1 Heat1 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit9 | Status DO 2 Heat2 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit10 | Status DO 3 Water pump | 0 | 1 | W PUMP A OFF / W PUMP A ON | |
| bit11 | Heater Under Power | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | At Freeze cnt overflow | 0 | 1 | ||
| 31212 | Air Flow Fan Manual | ‰ of fan power | 0 | 1000 | ‰ of fan power |
| 31213 | reserved | reserved | 0 | 0 | |
| 31214 | reserved | reserved | 0 | 0 | |
| 31215 | Temp W Out – Water return | °C (°F) | –40 (–40) | 100 (212) | |
| 31216 | Sensor Flow Alarm | 0 | 1 | ||
| 31217 | Power Heater | % | 0 | 100 | |
| Tacho Board | |||||
| 31218 | reserved | reserved | |||
| 31219 | reserved | reserved | |||
| SLAVE 3 | |||||
| Unit global status | |||||
| 31220 | bit0 | OFF / ON | 0 | 1 | OFF / ON |
| bit1 | Cooldown | 0 | 1 | COOLDWN NON / COOLDWN MODE | |
| bit2 | Water Heater antifreeze protection | 0 | 1 | AT FREEZE OK / AT FREEZE | |
| bit3 | Heater Overheat | 0 | 1 | ||
| bit4 | Open Door | 0 | 1 | CLOSED DOOR / OPEN DOOR | |
| bit5 | Door AfterRunning | 0 | 1 | AFTERRUNNING NON / AFTERRUNNING MODE | |
| bit6 | Sensor Flow Alarm St | 0 | 1 | OK / ERROR | |
| bit7 | reserved | 0 | 1 | ||
| bit8 | reserved | 0 | 1 | ||
| bit9 | Temp W Out St | 0 | 1 | OK / ERROR | |
| bit10 | Sw Fan Error | 0 | 1 | ||
| bit11 | Sw Heater Error | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | reserved | 0 | 1 | ||
| bit14 | Sw Global Error | 0 | 1 | ||
| bit15 | Communication Error | 0 | 1 | ||
| IO Status | |||||
| 31221 | bit0 | Status DI 1 Safety Therm 1 | 0 | 1 | OK / ERROR |
| bit1 | Status DI 2 Ext Control | 0 | 1 | OK / ERROR | |
| bit2 | Status DI 3 Room Thermostat | 0 | 1 | OK / ERROR | |
| bit3 | Status DI 4 Door | 0 | 1 | OK / ERROR | |
| bit4 | Status DI TACHO 1 | 0 | 1 | OK / ERROR | |
| bit5 | reserved | 0 | 1 | ||
| bit6 | reserved | 0 | 1 | ||
| bit7 | reserved | 0 | 1 | ||
| bit8 | Status DO 1 Heat1 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit9 | Status DO 2 Heat2 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit10 | Status DO 3 Water pump | 0 | 1 | W PUMP A OFF / W PUMP A ON | |
| bit11 | Heater Under Power | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | At Freeze cnt overflow | 0 | 1 | ||
| 31222 | Air Flow Fan Manual | ‰ of fan power | 0 | 1000 | ‰ of fan power |
| 31223 | reserved | reserved | 0 | 0 | |
| 31224 | reserved | reserved | 0 | 0 | |
| 31225 | Temp W Out – Water return | °C (°F) | –40 (–40) | 100 (212) | |
| 31226 | Sensor Flow Alarm | 0 | 1 | ||
| 31227 | Power Heater | % | 0 | 100 | |
| Tacho Board | |||||
| 31228 | reserved | reserved | |||
| 31229 | reserved | reserved | |||
| SLAVE 4 | |||||
| Unit global status | |||||
| 31230 | bit0 | OFF / ON | 0 | 1 | OFF / ON |
| bit1 | Cooldown | 0 | 1 | COOLDWN NON / COOLDWN MODE | |
| bit2 | Water Heater antifreeze protection | 0 | 1 | AT FREEZE OK / AT FREEZE | |
| bit3 | Heater Overheat | 0 | 1 | ||
| bit4 | Open Door | 0 | 1 | CLOSED DOOR / OPEN DOOR | |
| bit5 | Door AfterRunning | 0 | 1 | AFTERRUNNING NON / AFTERRUNNING MODE | |
| bit6 | Sensor Flow Alarm St | 0 | 1 | OK / ERROR | |
| bit7 | reserved | 0 | 1 | ||
| bit8 | reserved | 0 | 1 | ||
| bit9 | Temp W Out St | 0 | 1 | OK / ERROR | |
| bit10 | Sw Fan Error | 0 | 1 | ||
| bit11 | Sw Heater Error | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | reserved | 0 | 1 | ||
| bit14 | Sw Global Error | 0 | 1 | ||
| bit15 | Communication Error | 0 | 1 | ||
| IO Status | |||||
| 31231 | bit0 | Status DI 1 Safety Therm 1 | 0 | 1 | OK / ERROR |
| bit1 | Status DI 2 Ext Control | 0 | 1 | OK / ERROR | |
| bit2 | Status DI 3 Room Thermostat | 0 | 1 | OK / ERROR | |
| bit3 | Status DI 4 Door | 0 | 1 | OK / ERROR | |
| bit4 | Status DI TACHO 1 | 0 | 1 | OK / ERROR | |
| bit5 | reserved | 0 | 1 | ||
| bit6 | reserved | 0 | 1 | ||
| bit7 | reserved | 0 | 1 | ||
| bit8 | Status DO 1 Heat1 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit9 | Status DO 2 Heat2 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit10 | Status DO 3 Water pump | 0 | 1 | W PUMP A OFF / W PUMP A ON | |
| bit11 | Heater Under Power | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | At Freeze cnt overflow | 0 | 1 | ||
| 31232 | Air Flow Fan Manual | ‰ of fan power | 0 | 1000 | ‰ of fan power |
| 31233 | reserved | reserved | 0 | 0 | |
| 31234 | reserved | reserved | 0 | 0 | |
| 31235 | Temp W Out – Water return | °C (°F) | –40 (–40) | 100 (212) | |
| 31236 | Sensor Flow Alarm | 0 | 1 | ||
| 31237 | Power Heater | % | 0 | 100 | |
| Tacho Board | |||||
| 31238 | reserved | reserved | |||
| 31239 | reserved | reserved | |||
| SLAVE 5 | |||||
| Unit global status | |||||
| 31240 | bit0 | OFF / ON | 0 | 1 | OFF / ON |
| bit1 | Cooldown | 0 | 1 | COOLDWN NON / COOLDWN MODE | |
| bit2 | Water Heater antifreeze protection | 0 | 1 | AT FREEZE OK / AT FREEZE | |
| bit3 | Heater Overheat | 0 | 1 | ||
| bit4 | Open Door | 0 | 1 | CLOSED DOOR / OPEN DOOR | |
| bit5 | Door AfterRunning | 0 | 1 | AFTERRUNNING NON / AFTERRUNNING MODE | |
| bit6 | Sensor Flow Alarm St | 0 | 1 | OK / ERROR | |
| bit7 | reserved | 0 | 1 | ||
| bit8 | reserved | 0 | 1 | ||
| bit9 | Temp W Out St | 0 | 1 | OK / ERROR | |
| bit10 | Sw Fan Error | 0 | 1 | ||
| bit11 | Sw Heater Error | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | reserved | 0 | 1 | ||
| bit14 | Sw Global Error | 0 | 1 | ||
| bit15 | Communication Error | 0 | 1 | ||
| IO Status | |||||
| 31241 | bit0 | Status DI 1 Safety Therm 1 | 0 | 1 | OK / ERROR |
| bit1 | Status DI 2 Ext Control | 0 | 1 | OK / ERROR | |
| bit2 | Status DI 3 Room Thermostat | 0 | 1 | OK / ERROR | |
| bit3 | Status DI 4 Door | 0 | 1 | OK / ERROR | |
| bit4 | Status DI TACHO 1 | 0 | 1 | OK / ERROR | |
| bit5 | reserved | 0 | 1 | ||
| bit6 | reserved | 0 | 1 | ||
| bit7 | reserved | 0 | 1 | ||
| bit8 | Status DO 1 Heat1 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit9 | Status DO 2 Heat2 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit10 | Status DO 3 Water pump | 0 | 1 | W PUMP A OFF / W PUMP A ON | |
| bit11 | Heater Under Power | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | At Freeze cnt overflow | 0 | 1 | ||
| 31242 | Air Flow Fan Manual | ‰ of fan power | 0 | 1000 | ‰ of fan power |
| 31243 | reserved | reserved | 0 | 0 | |
| 31244 | reserved | reserved | 0 | 0 | |
| 31245 | Temp W Out – Water return | °C (°F) | –40 (–40) | 100 (212) | |
| 31246 | Sensor Flow Alarm | 0 | 1 | ||
| 31247 | Power Heater | % | 0 | 100 | |
| Tacho Board | |||||
| 31248 | reserved | reserved | |||
| 31249 | reserved | reserved | |||
| SLAVE 6 | |||||
| Unit global status | |||||
| 31250 | bit0 | OFF / ON | 0 | 1 | OFF / ON |
| bit1 | Cooldown | 0 | 1 | COOLDWN NON / COOLDWN MODE | |
| bit2 | Water Heater antifreeze protection | 0 | 1 | AT FREEZE OK / AT FREEZE | |
| bit3 | Heater Overheat | 0 | 1 | ||
| bit4 | Open Door | 0 | 1 | CLOSED DOOR / OPEN DOOR | |
| bit5 | Door AfterRunning | 0 | 1 | AFTERRUNNING NON / AFTERRUNNING MODE | |
| bit6 | Sensor Flow Alarm St | 0 | 1 | OK / ERROR | |
| bit7 | reserved | 0 | 1 | ||
| bit8 | reserved | 0 | 1 | ||
| bit9 | Temp W Out St | 0 | 1 | OK / ERROR | |
| bit10 | Sw Fan Error | 0 | 1 | ||
| bit11 | Sw Heater Error | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | reserved | 0 | 1 | ||
| bit14 | Sw Global Error | 0 | 1 | ||
| bit15 | Communication Error | 0 | 1 | ||
| IO Status | |||||
| 31251 | bit0 | Status DI 1 Safety Therm 1 | 0 | 1 | OK / ERROR |
| bit1 | Status DI 2 Ext Control | 0 | 1 | OK / ERROR | |
| bit2 | Status DI 3 Room Thermostat | 0 | 1 | OK / ERROR | |
| bit3 | Status DI 4 Door | 0 | 1 | OK / ERROR | |
| bit4 | Status DI TACHO 1 | 0 | 1 | OK / ERROR | |
| bit5 | reserved | 0 | 1 | ||
| bit6 | reserved | 0 | 1 | ||
| bit7 | reserved | 0 | 1 | ||
| bit8 | Status DO 1 Heat1 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit9 | Status DO 2 Heat2 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit10 | Status DO 3 Water pump | 0 | 1 | W PUMP A OFF / W PUMP A ON | |
| bit11 | Heater Under Power | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | At Freeze cnt overflow | 0 | 1 | ||
| 31252 | Air Flow Fan Manual | ‰ of fan power | 0 | 1000 | ‰ of fan power |
| 31253 | reserved | reserved | 0 | 0 | |
| 31254 | reserved | reserved | 0 | 0 | |
| 31255 | Temp W Out – Water return | °C (°F) | –40 (–40) | 100 (212) | |
| 31256 | Sensor Flow Alarm | 0 | 1 | ||
| 31257 | Power Heater | % | 0 | 100 | |
| Tacho Board | |||||
| 31258 | reserved | reserved | |||
| 31259 | reserved | reserved | |||
| SLAVE 7 | |||||
| Unit global status | |||||
| 31260 | bit0 | OFF / ON | 0 | 1 | OFF / ON |
| bit1 | Cooldown | 0 | 1 | COOLDWN NON / COOLDWN MODE | |
| bit2 | Water Heater antifreeze protection | 0 | 1 | AT FREEZE OK / AT FREEZE | |
| bit3 | Heater Overheat | 0 | 1 | ||
| bit4 | Open Door | 0 | 1 | CLOSED DOOR / OPEN DOOR | |
| bit5 | Door AfterRunning | 0 | 1 | AFTERRUNNING NON / AFTERRUNNING MODE | |
| bit6 | Sensor Flow Alarm St | 0 | 1 | OK / ERROR | |
| bit7 | reserved | 0 | 1 | ||
| bit8 | reserved | 0 | 1 | ||
| bit9 | Temp W Out St | 0 | 1 | OK / ERROR | |
| bit10 | Sw Fan Error | 0 | 1 | ||
| bit11 | Sw Heater Error | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | reserved | 0 | 1 | ||
| bit14 | Sw Global Error | 0 | 1 | ||
| bit15 | Communication Error | 0 | 1 | ||
| IO Status | |||||
| 31261 | bit0 | Status DI 1 Safety Therm 1 | 0 | 1 | OK / ERROR |
| bit1 | Status DI 2 Ext Control | 0 | 1 | OK / ERROR | |
| bit2 | Status DI 3 Room Thermostat | 0 | 1 | OK / ERROR | |
| bit3 | Status DI 4 Door | 0 | 1 | OK / ERROR | |
| bit4 | Status DI TACHO 1 | 0 | 1 | OK / ERROR | |
| bit5 | reserved | 0 | 1 | ||
| bit6 | reserved | 0 | 1 | ||
| bit7 | reserved | 0 | 1 | ||
| bit8 | Status DO 1 Heat1 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit9 | Status DO 2 Heat2 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit10 | Status DO 3 Water pump | 0 | 1 | W PUMP A OFF / W PUMP A ON | |
| bit11 | Heater Under Power | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | At Freeze cnt overflow | 0 | 1 | ||
| 31262 | Air Flow Fan Manual | ‰ of fan power | 0 | 1000 | ‰ of fan power |
| 31263 | reserved | reserved | 0 | 0 | |
| 31264 | reserved | reserved | 0 | 0 | |
| 31265 | Temp W Out – Water return | °C (°F) | –40 (–40) | 100 (212) | |
| 31266 | Sensor Flow Alarm | 0 | 1 | ||
| 31267 | Power Heater | % | 0 | 100 | |
| Tacho Board | |||||
| 31268 | reserved | reserved | |||
| 31269 | reserved | reserved | |||
| SLAVE 8 | |||||
| Unit global status | |||||
| 31270 | bit0 | OFF / ON | 0 | 1 | OFF / ON |
| bit1 | Cooldown | 0 | 1 | COOLDWN NON / COOLDWN MODE | |
| bit2 | Water Heater antifreeze protection | 0 | 1 | AT FREEZE OK / AT FREEZE | |
| bit3 | Heater Overheat | 0 | 1 | ||
| bit4 | Open Door | 0 | 1 | CLOSED DOOR / OPEN DOOR | |
| bit5 | Door AfterRunning | 0 | 1 | AFTERRUNNING NON / AFTERRUNNING MODE | |
| bit6 | Sensor Flow Alarm St | 0 | 1 | OK / ERROR | |
| bit7 | reserved | 0 | 1 | ||
| bit8 | reserved | 0 | 1 | ||
| bit9 | Temp W Out St | 0 | 1 | OK / ERROR | |
| bit10 | Sw Fan Error | 0 | 1 | ||
| bit11 | Sw Heater Error | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | reserved | 0 | 1 | ||
| bit14 | Sw Global Error | 0 | 1 | ||
| bit15 | Communication Error | 0 | 1 | ||
| IO Status | |||||
| 31271 | bit0 | Status DI 1 Safety Therm 1 | 0 | 1 | OK / ERROR |
| bit1 | Status DI 2 Ext Control | 0 | 1 | OK / ERROR | |
| bit2 | Status DI 3 Room Thermostat | 0 | 1 | OK / ERROR | |
| bit3 | Status DI 4 Door | 0 | 1 | OK / ERROR | |
| bit4 | Status DI TACHO 1 | 0 | 1 | OK / ERROR | |
| bit5 | reserved | 0 | 1 | ||
| bit6 | reserved | 0 | 1 | ||
| bit7 | reserved | 0 | 1 | ||
| bit8 | Status DO 1 Heat1 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit9 | Status DO 2 Heat2 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit10 | Status DO 3 Water pump | 0 | 1 | W PUMP A OFF / W PUMP A ON | |
| bit11 | Heater Under Power | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | At Freeze cnt overflow | 0 | 1 | ||
| 31272 | Air Flow Fan Manual | ‰ of fan power | 0 | 1000 | ‰ of fan power |
| 31273 | reserved | reserved | 0 | 0 | |
| 31274 | reserved | reserved | 0 | 0 | |
| 31275 | Temp W Out – Water return | °C (°F) | –40 (–40) | 100 (212) | |
| 31276 | Sensor Flow Alarm | 0 | 1 | ||
| 31277 | Power Heater | % | 0 | 100 | |
| Tacho Board | |||||
| 31278 | reserved | reserved | |||
| 31279 | reserved | reserved | |||
| SLAVE 9 | |||||
| Unit global status | |||||
| 31280 | bit0 | OFF / ON | 0 | 1 | OFF / ON |
| bit1 | Cooldown | 0 | 1 | COOLDWN NON / COOLDWN MODE | |
| bit2 | Water Heater antifreeze protection | 0 | 1 | AT FREEZE OK / AT FREEZE | |
| bit3 | Heater Overheat | 0 | 1 | ||
| bit4 | Open Door | 0 | 1 | CLOSED DOOR / OPEN DOOR | |
| bit5 | Door AfterRunning | 0 | 1 | AFTERRUNNING NON / AFTERRUNNING MODE | |
| bit6 | Sensor Flow Alarm St | 0 | 1 | OK / ERROR | |
| bit7 | reserved | 0 | 1 | ||
| bit8 | reserved | 0 | 1 | ||
| bit9 | Temp W Out St | 0 | 1 | OK / ERROR | |
| bit10 | Sw Fan Error | 0 | 1 | ||
| bit11 | Sw Heater Error | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | reserved | 0 | 1 | ||
| bit14 | Sw Global Error | 0 | 1 | ||
| bit15 | Communication Error | 0 | 1 | ||
| IO Status | |||||
| 31281 | bit0 | Status DI 1 Safety Therm 1 | 0 | 1 | OK / ERROR |
| bit1 | Status DI 2 Ext Control | 0 | 1 | OK / ERROR | |
| bit2 | Status DI 3 Room Thermostat | 0 | 1 | OK / ERROR | |
| bit3 | Status DI 4 Door | 0 | 1 | OK / ERROR | |
| bit4 | Status DI TACHO 1 | 0 | 1 | OK / ERROR | |
| bit5 | reserved | 0 | 1 | ||
| bit6 | reserved | 0 | 1 | ||
| bit7 | reserved | 0 | 1 | ||
| bit8 | Status DO 1 Heat1 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit9 | Status DO 2 Heat2 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit10 | Status DO 3 Water pump | 0 | 1 | W PUMP A OFF / W PUMP A ON | |
| bit11 | Heater Under Power | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | At Freeze cnt overflow | 0 | 1 | ||
| 31282 | Air Flow Fan Manual | ‰ of fan power | 0 | 1000 | ‰ of fan power |
| 31283 | reserved | reserved | 0 | 0 | |
| 31284 | reserved | reserved | 0 | 0 | |
| 31285 | Temp W Out – Water return | °C (°F) | –40 (–40) | 100 (212) | |
| 31286 | Sensor Flow Alarm | 0 | 1 | ||
| 31287 | Power Heater | % | 0 | 100 | |
| Tacho Board | |||||
| 31288 | reserved | reserved | |||
| 31289 | reserved | reserved | |||
| SLAVE 10 | |||||
| Unit global status | |||||
| 31290 | bit0 | OFF/ON | 0 | 1 | OFF / ON |
| bit1 | Cooldown | 0 | 1 | COOLDWN NON / COOLDWN MODE | |
| bit2 | Water Heater antifreeze protection | 0 | 1 | AT FREEZE OK / AT FREEZE | |
| bit3 | Heater Overheat | 0 | 1 | ||
| bit4 | Open Door | 0 | 1 | CLOSED DOOR / OPEN DOOR | |
| bit5 | Door AfterRunning | 0 | 1 | AFTERRUNNING NON / AFTERRUNNING MODE | |
| bit6 | Sensor Flow Alarm St | 0 | 1 | OK / ERROR | |
| bit7 | reserved | 0 | 1 | ||
| bit8 | reserved | 0 | 1 | ||
| bit9 | Temp W Out St | 0 | 1 | OK / ERROR | |
| bit10 | Sw Fan Error | 0 | 1 | ||
| bit11 | Sw Heater Error | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | reserved | 0 | 1 | ||
| bit14 | Sw Global Error | 0 | 1 | ||
| bit15 | Communication Error | 0 | 1 | ||
| IO Status | |||||
| 31291 | bit0 | Status DI 1 Safety Therm 1 | 0 | 1 | OK / ERROR |
| bit1 | Status DI 2 Ext Control | 0 | 1 | OK / ERROR | |
| bit2 | Status DI 3 Room Thermostat | 0 | 1 | OK / ERROR | |
| bit3 | Status DI 4 Door | 0 | 1 | OK / ERROR | |
| bit4 | Status DI TACHO 1 | 0 | 1 | OK / ERROR | |
| bit5 | reserved | 0 | 1 | ||
| bit6 | reserved | 0 | 1 | ||
| bit7 | reserved | 0 | 1 | ||
| bit8 | Status DO 1 Heat1 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit9 | Status DO 2 Heat2 | 0 | 1 | HEAT CLOSED / HEAT OPEN | |
| bit10 | Status DO 3 Water pump | 0 | 1 | W PUMP A OFF / W PUMP A ON | |
| bit11 | Heater Under Power | 0 | 1 | ||
| bit12 | reserved | 0 | 1 | ||
| bit13 | At Freeze cnt overflow | 0 | 1 | ||
| 31292 | AirFlow Fan Manual | ‰ of fan power | 0 | 1000 | ‰ of fan power |
| 31293 | reserved | reserved | 0 | 0 | |
| 31294 | reserved | reserved | 0 | 0 | |
| 31295 | Temp W Out – Water return | °C (°F) | –40 (–40) | 100 (212) | |
| 31296 | Sensor Flow Alarm | 0 | 1 | ||
| 31297 | Power Heater | % | 0 | 100 | |
| Tacho Board | |||||
| 31298 | reserved | reserved | |||
| 31299 | reserved | reserved |
Protokollet för Holding share används för produktstyrning. Det visar aktuella styrkommandon och styrsignaler som kan skickas till produkten. Protokollet visar även kommandon från styrpanel eller annan styrutrustning, t.ex. Android-app, serviceprogramvara etc. (Fabriksåterställning till standard.)
| Adress | Namn | Info | Min. Value | Max. Value | Default | Enum |
|---|---|---|---|---|---|---|
| 40300 | On / off | – | 0 | 1 | 1 | |
| 40301 | Temper closed door | Temperature setpoint for closed door state | 5°C / 41°F | 45°C / 113°F | 21°C / 70°F | |
| 40302 | Heat power closed door | Heating power in percent for closed door | 0 | 100 | 0 | |
| 40303 | Fan speed closed door | Fan speed in promile for closed door | 0 | 1000 | EC-fan 150 | |
| " | " | " | 0 | 1000 | AC3-fan 330 / AC5-fan 200 | |
| 40304 | Temper open door | Temperature setpoint for open door state | 5°C / 41°F | 45°C / 113°F | 25°C / 77°F | |
| 40305 | Heat power open door | Heating power in percent for open door | 0 | 100 | 0 | |
| 40306 | Fan speed open door | Fan speed in promile for open door | 0 | 1000 | EC-fan 150 | |
| " | " | " | 0 | 1000 | AC3-fan 330 / AC5-fan 200 | |
| 40307 | Error reset | Reset all errors | 0 | 1 | 0 | |
| 40308 | Temp sensor reset | Reset room temperature sensor location to default | 0 | 1 | 0 | |
| 40309 | Filter timer reset | Reset maintenance signalization | 0 | 1 | 0 | |
| 40310 | Read cfg req | Reserved | 0 | 1 | 0 | |
| 40311 | Time Sw Global Enable | Schedule enable | 0 | 1 | 0 | |
| 40312 | Time Sw Heat | Heating power in percent in timer interval | 0 | 100 | 0 | |
| 40313 | Time Sw Temp | Temperature setpoint in timer interval | 5°C / 41°F | 45°C / 113°F | 21°C / 70°F | |
| 40314 | Time Sw Flow | Fan speed in percent in timer interval | 0 | 100 | 100 | |
| 40315 | Time Sw Mode | Automat or manual heating mode in timer interval | 0 | 2 | 0 | 0 = Manual |
| " | " | " | 0 | 2 | 0 | 1 = Automat |
| " | " | " | 0 | 2 | 0 | 2 = Off mode |
| 40316 | Time Sw | Activation or deactivation actual timer interval | 0 | 1 | 0 | |
| 40317 | Default cfg restore | Forced configuration restore by button has be done | 0 | 1 | 0 | |
| 40318 | Test mode | Activation / deactivation of test mode | 0 | 1 | 0 | |
| 40319 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40320 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40321 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40322 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40323 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40324 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40325 | Reserved | Reserved | 0 | 65535 | 0 | |
| 40326 | Reserved | Reserved | 0 | 65535 | 0 |
Protokollet för Holding BMS temp. sensors används för att ta emot värden från externa sensorer via BMS.
| Address | Name | Info |
|---|---|---|
| 40100 | Temperature Outside BMS | Write temperature *10 |
| 40101 | Outside Temperature Sensor Bms St | Status of sensor |
| 40102 | Room BMS | Write temperature *10 |
| 40103 | Room Temperature Sensor Bms St | Status of sensor |
Tillbehör
Du kanske också gillar …
Hej! Mina kollegor och jag hjälper dig gärna om du har frågor kring produkter, priser och beställningar. Vi hjälper dig även gärna med förslag på värmelösningar.
| För oss på Eveco är det viktigt att ta hänsyn till miljön. Vi arbetar för en hållbar utveckling och tar hänsyn till kommande generationer. Läs mer i vår Miljöpolicy! |